John Deere Compact Loader 850C User Manual

S P E C I F I C A T I O N S  
C
S E R I E S I I  
850C  
C O N S T R U C T I O N E Q U I P M E N T  
Engine  
850C  
Type ................................................................................................John Deere 6081A with altitude-compensating turbocharger; aftercooled  
Engine power ..................................................................................185 SAE net hp (138 kW) / 192 SAE gross hp (143 kW) @ 1,800 rpm  
Cylinders .........................................................................................6  
Displacement ..................................................................................494 cu. in. (8.1 L)  
Fuel consumption, typical................................................................4.6 to 7.0 gal./hr. (17.4 to 26.5 L/h)  
Maximum net torque .......................................................................601 lb.-ft. (815 Nm) @ 1,300 rpm  
Lubrication ......................................................................................pressure system with full-flow spin-on filter and oil-to-water cooler  
Air cleaner.......................................................................................dual stage dry type with safety element, precleaner, and underhood restriction indicator  
Electrical system .............................................................................24 volt with 45-amp alternator  
Cooling fan......................................................................................blower  
Transmission  
automatic, dual-path, hydrostatic drive; load sensing feature automatically adjusts speed and power to match changing load conditions; each individually controlled track is powered by a variable displace-  
ment piston pump and motor combination; travel speeds (forward and reverse) infinite to 6.8 mph (0 to 11 km/h); ground-speed selection buttons on single-lever steering and direction control; inde-  
pendently selectable reverse speed ratios 80%, 100%, 115%, or 130% of forward ground speed; decelerator pedal controls ground speed to dead stop  
Final Drives  
double-reduction, planetary final drives transfer torque loads over three gear sets; mounted independently of track frames and dozer push frames for isolation from shock loads  
Steering  
single-lever steering, direction, and ground-speed control provides smooth metered turns; full power turns, counterrotation, and infinitely variable track speeds provide unlimited maneuverability and  
optimal control; hydrostatic steering system eliminates steering clutches and brakes  
Brakes  
hydrostatic (dynamic) braking stops machine when the direction/steering control lever is moved to neutral, the decelerator is depressed to the end of travel, or the brake pedal is depressed  
Automatic Parking Brake  
this safety feature engages wet, multiple-disk brakes automatically whenever the engine stops, the operator applies the brake pedal, or the neutral start lever lock is in stop position; machine cannot be  
operated with brake applied  
Hydraulic System  
System type ....................................................................................open center  
Pressure, system relief ....................................................................2,250 psi (15 514 kPa)  
Pump type.......................................................................................gear  
Flow ................................................................................................44 gpm (166 L/min.) @ 2,100 rpm  
Filter, return oil ................................................................................10 micron  
Control ............................................................................................standard – T-bar, two function / with All-Hydraulic (PAT) dozer blade – T-bar, three function  
Cylinders .........................................................................................heat-treated, chrome-plated, polished cylinder rods with hardened steel (replaceable bushings) pivot pins  
Cooling............................................................................................oil-to-air heat exchanger  
Capacities (U.S.)  
850C LT  
850C WT  
850C WXLT  
850C LGP  
Fuel tank with lockable cap.............................................................92 gal. (348 L)  
Cooling system with recovery tank ..................................................9 gal. (34 L)  
Engine oil with spin-on filter............................................................34 qt. (32.2 L)  
Final drive (each)  
92 gal. (348 L)  
9 gal. (34 L)  
34 qt. (32.2 L)  
92 gal. (348 L)  
9 gal. (34 L)  
34 qt. (32.2 L)  
92 gal. (348 L)  
9 gal. (34 L)  
34 qt. (32.2 L)  
1st reduction............................................................................3.25 gal. (12.3 L) Semi-U /  
4.35 gal. (16.5 L) PAT  
2nd reduction...........................................................................3.25 gal. (12.3 L)  
Hydraulic system reservoir ..............................................................21 gal. (79.5 L)  
Hydrostatic transmission reservoir...................................................27 gal. (102.2 L)  
4.35 gal. (16.5 L) Semi-U /  
10.0 gal. (37.9 L) PAT  
3.25 gal. (12.3 L)  
21 gal. (79.5 L)  
27 gal. (102.2 L)  
10.0 gal. (37.9 L) PAT  
10.0 gal. (37.9 L) Semi-U /  
10.0 gal. (37.9 L) PAT  
3.25 gal. (12.3 L)  
21 gal. (80 L)  
3.25 gal. (12.3 L)  
21 gal. (79.5 L)  
27 gal. (102.2 L)  
27 gal. (103 L)  
Undercarriage  
seven-roller track frame with front and rear track guides and sprocket guard; John Deere Dura-Trax™ features deep-heat-treated, sealed, and lubricated track links and through-hardened, sealed, and  
lubricated rollers for maximum wear resistance; sprockets are segmented; extreme-duty shoes are available (on some models) for severe applications  
Chain...............................................................................................sealed and lubed  
Grouser width..................................................................................24 in. (610 mm)  
sealed and lubed  
30 in. (762 mm)  
sealed and lubed  
30 in. (762 mm)  
sealed and lubed  
38 in. (965 mm) base /  
34 in. (865 mm) PAT  
43  
9,196 sq. in. (59 329 cm2)  
base / 8,228 sq. in. (53 084  
cm2) PAT  
Shoes, each side .............................................................................40  
Ground contact area........................................................................5,184 sq. in. (33 445 cm2)  
40  
43  
6,480 sq. in. (41 806 cm2)  
7,260 sq. in. (46 838 cm2)  
Ground pressure..............................................................................7.8 psi (53.8 kPa) Semi-U /  
8.2 psi (56.5 kPa) PAT  
6.3 psi (43.4 kPa) Semi-U /  
6.7 psi (46.2 kPa) PAT  
6.1 psi (42.0 kPa) PAT  
4.6 psi (31.7 kPa) Semi-U /  
5.4 psi (37.2 kPa) PAT  
Ground clearance, minimum  
With single-bar grouser (excluding grouser height)...................16.0 in. (406 mm)  
16.0 in. (406 mm)  
16.0 in. (406 mm)  
16.0 in. (406 mm)  
With swamp shoe (including grouser height)...................................................................................................................................................................................................19.0 in. (483 mm) base  
Length of track on ground ...............................................................108 in. (2743 mm)  
Track gauge, standard.....................................................................74 in. (1880 mm) Semi-U /  
82 in. (2083 mm) PAT  
Oscillation at front roller ..................................................................6 degrees, or 9.1 in. (231  
mm) Semi-U / 6 degrees,  
or 9.7 in. (246 mm) PAT  
Track rollers each side.....................................................................7  
Track pitch ...................................................................................8 in. (203 mm)  
108 in. (2743 mm)  
80 in. (2032 mm) Semi-U /  
88 in. (2235 mm) PAT  
6 degrees, or 9.0 in. (229  
mm) Semi-U / 7 degrees,  
or 10.8 in. (274 mm) PAT  
7
121 in. (3073 mm)  
88 in. (2235 mm) PAT  
121 in. (3073 mm)  
88 in. (2235 mm) Semi-U /  
92 in. (2337 mm) PAT  
7 degrees, or 12.5 in. (318  
mm) Semi-U / 7 degrees,  
or 12.8 in. (325 mm) PAT  
7
6 degrees, or 10.4 in. (264  
mm) PAT  
7
8 in. (203 mm)  
8 in. (203 mm)  
8 in. (203 mm)  
16  
 
Dimensions  
A
Overall height to roof  
Overall height  
to exhaust stack  
B
Tread depth with single-bar grousers  
Tread depth with  
swamp shoes  
C
Ground clearance  
with grousers  
Moderate duty  
2.6 in. (65 mm)  
2.6 in. (65 mm)  
2.6 in. (65 mm)  
2.6 in. (65 mm)  
Extreme duty  
2.8 in. (72 mm)  
850C LT ..........................124.0 in. (3151 mm)  
850C WT.........................124.0 in. (3151 mm)  
850C WXLT .....................124.0 in. (3151 mm)  
850C LGP........................124.0 in. (3151 mm)  
124.8 in. (3170 mm)  
124.8 in. (3170 mm)  
124.8 in. (3170 mm)  
124.8 in. (3170 mm)  
16 in. (406 mm)  
16 in. (406 mm)  
16 in. (406 mm)  
16 in. (406 mm)  
3.7 in. (93 mm)  
D
Blade width  
E
Blade height  
F
Blade lift height  
G
Blade dig-  
ging depth  
H
Blade tilt  
(uses tilt jack)  
I
Overall  
length  
with blade  
J
Overall width  
with blade  
angled  
850C LT  
All-Hydraulic  
(PAT) Dozer ..............146.0 in.  
(3708 mm)  
48.3 in.  
(1227 mm)  
38.0 in.  
(962 mm)  
33.4 in.  
(849 mm)  
19.0 in.  
(482 mm)  
203.1 in.  
(5160 mm)**  
131.6 in.  
(3343 mm)  
Semi-U (High  
Production) ..............128.3 in.  
(3259 mm)  
56.5 in.  
(1435 mm)  
43.3 in.  
(1100 mm)  
20.2 in.  
(513 mm)  
28.7 in.  
(730 mm)  
207.1 in.  
(5262 mm)*  
N/A  
*Optional extended drawbar adds 10.1 in. (253 mm).  
**Optional extended drawbar adds 8.9 in. (223 mm).  
850C WT  
All-Hydraulic  
Dozer (PAT) ..............158.0 in.  
(4013 mm)  
48.3 in.  
(1227 mm)  
38.0 in.  
(962 mm)  
33.4 in.  
(849 mm)  
20.5 in.  
(522 mm)  
203.1 in.  
(5160 mm)**  
142.4 in.  
(3618 mm)  
Semi-U (High  
Production) ..............140.0 in.  
(3556 mm)  
56.5 in.  
(1435 mm)  
43.3 in.  
(1100 mm)  
20.2 in.  
(513 mm)  
34.6 in.  
(878 mm)  
207.1 in.  
(5262 mm)***  
N/A  
**Optional extended drawbar adds 8.9 in. (223 mm).  
***Optional extended drawbar adds 7 in. (176 mm).  
850C WXLT  
All-Hydraulic  
Dozer (PAT) ..............158.0 in.  
(4013 mm)  
48.3 in.  
(1227 mm)  
40.7 in.  
(1034 mm)  
35.2 in.  
(893 mm)  
20.5 in.  
(522 mm)  
218.5 in.  
(5553 mm)**  
142.4 in.  
(3618 mm)  
**Optional extended drawbar adds 8.9 in. (223 mm).  
850C LGP  
Semi-U (Low Profile) and Straight blades available through Custom Engineering.  
All-Hydraulic  
(PAT) Dozer ..............168.0 in.  
(4267 mm)  
48.3 in.  
(1227 mm)  
40.7 in.  
(1034 mm)  
35.2 in.  
(893 mm)  
21.8 in.  
(554 mm)  
218.5 in.  
(5553 mm)**  
152.0 in.  
(3860 mm) /  
144 in.  
#
(3658 mm)  
Semi-U (High  
Production) ..............156.6 in.  
(3978 mm)  
43.8 in.  
(1113 mm)  
42.5 in.  
(1080 mm)  
16.9 in.  
(429 mm)  
37.0 in.  
(940 mm)  
222.5 in.  
(5651 mm)**  
N/A  
**Optional extended drawbar adds 8.9 in. (223 mm).  
#
With L/R angle cylinder pins removed at blade.  
K
Blade angle  
L
Cut reach  
M
Width over track  
106 in. (2692 m)  
N
Cast reach  
O
Cutting edge angle  
60 degrees  
850C LT  
All-Hydraulic  
(PAT) Dozer ..............25 degrees  
4.5 in. (113 m)  
21.2 in. (538 m)  
20.5 in. (523 m)  
20.5 in. (523 m)  
21.2 in. (538 mm)  
850C WT  
All-Hydraulic  
(PAT) Dozer ..............25 degrees  
3.9 in. (98 m)  
3.9 in. (98 m)  
118 in. (2997 m)  
118 in. (2997 m)  
126 in. (3200 mm)  
60 degrees  
60 degrees  
60 degrees  
850C WXLT  
All-Hydraulic  
(PAT) Dozer ..............25 degrees  
850C LGP  
All-Hydraulic  
(PAT) Dozer ..............25 degrees  
4.5 in. (113 mm)  
Drawbar Pull  
850C  
Maximum ........................................................................................72,000 lb. (320 kN)  
At 1.2 mph (1.9 km/h).....................................................................35,200 lb. (156 kN)  
At 2.0 mph (3.2 km/h).....................................................................25,300 lb. (112 kN)  
18  
 
A
E
F
C
G
Standard Drawbar  
B
Extended Drawbar  
I
O
K
L
Cut Reach  
Width Over Track  
M
J
H
N
Cast Reach  
D
75  
70  
65  
60  
55  
50  
45  
40  
35  
30  
25  
20  
15  
10  
5
320  
32  
28  
24  
20  
16  
12  
8
850C LT, WT,  
WXLT, and LGP  
280  
240  
200  
160  
120  
80  
CRAWLER SPEED  
VS  
GROUND PULL  
Usable pull will depend  
on traction and weight of tractor.  
40  
N
4
lb.  
kg  
km/h  
0
0
2
4
6
8
10  
12  
mph  
1
2
3
4
5
6
7
8
SPEED  
19  
 
850C Series II Dozer  
Key: G Standard equipment L Optional or special equipment  
See your John Deere dealer for further information.  
LT WT WXLT LGP  
Engine  
LT WT WXLT LGP Undercarriage (continued)  
LT WT WXLT LGP Operator’s Station (continued)  
G G G G Air cleaner, dual-stage aspirated type  
G G G G Air cleaner restriction indicator  
G G G G Blower fan  
G G G G Coolant recovery tank  
G G G G Electric ether start aid  
G G G G Enclosed safety fan guard (conforms  
to SAE J1308)  
G G G G Engine coolant –34°F (–37°C)  
G G G G Oil-to-water engine oil cooler  
G G G G Precleaner  
L L  
L L  
G L  
22-in. (560 mm) moderate-duty single-  
bar grouser tracks, Dura-Trax™ lub-  
ricated chain with split master link  
22-in. (560 mm) extreme-duty single-  
bar grouser tracks, Dura-Trax lubri-  
cated chain with split master link  
24-in. (610 mm) moderate-duty single-  
bar grouser tracks, Dura-Trax lubri-  
cated chain with split master link  
(for 850C LT)  
G G G G Fuel gauge, electric, illuminated  
G G G G Ground-speed decelerator (engine  
and transmission)  
G G G G Headliner for ROPS/FOPS  
G G G G Horn, electric (conforms to SAE  
J994, J1446)  
G G G G Hourmeter, electric, illuminated  
(selectable)  
G G G G Interior-mounted rearview mirror  
(conforms to SAE J985)  
G G G G Spin-on fuel filter  
G G G G Trash-resistant radiator  
G G G G Turbocharger  
G G G G Underhood muffler with vertical  
exhaust stack  
G G G G Water separator  
L L L L Engine coolant heater, 1,000 watts,  
120 volts  
L L  
24-in. (610 mm) extreme-duty single-  
bar grouser tracks, Dura-Trax lubri-  
cated chain with split master link  
(N/A for 850C PAT blade)  
G G G G Key start switch with electric fuel  
shutoff  
G G G G Lunch-box storage  
G G G G Modular design ROPS/FOPS canopy  
(conforms to SAE J1040)  
G G G G Parking brake, single-lever activation  
L L L L Protection package, full vehicle –  
Brush screens, heavy-duty / Guards,  
tank protection / Limb risers, arched  
G G G G Reverse ratio – user selectable at  
80%, 100%, 115%, or 130% of for-  
ward speed  
G G G G Seat belt, 3 in. (76 mm), with retrac-  
tors (conforms to SAE J386)  
G G G G Single-lever steering, direction, and  
ground-speed control with selectable  
ground-speed and horn controls inte-  
grated in “T” handle  
G G  
30-in. (760 mm) moderate-duty single-  
bar grouser tracks, Dura-Trax lubri-  
cated chain with split master link  
G 34-in. (865 mm) moderate-duty single-  
bar grouser tracks, Dura-Trax lubri-  
cated chain with split master link  
(with PAT blade)  
G 38-in. (965 mm) moderate-duty single-  
bar grouser tracks, Dura-Trax lubri-  
cated chain with split master link  
(for 850C LGP Semi-U blade)  
L L L L Prescreener guard  
L L L L Radiator sand screen  
L L L L Reversible fan  
L L L L Chrome exhaust stack  
Power Train  
G G G G Automatic applied, hydrostatic-  
released park brake, pedal operated  
G G G G Oil-to-air transmission cooler  
G G G G Dual-path hydrostatic transmission  
G G G G Guard, built-in final drive seal  
G G G G Transmission neutral lock with  
starter safety switch  
G G G G Transmission diagnostic test ports  
L L L L Remote transmission diagnostic test  
ports  
L 36.5-in. (928 mm) swamp shoe tracks,  
Dura-Trax lubricated chain with split  
master link (N/A with PAT blade)  
Bolt-on full-length rock guards  
L L  
G G G G Tool storage, lockable  
G G G G Voltmeter digital display (selectable)  
Lights  
Overall Vehicle  
G G G G Front tow hook  
L L L L Two front driving/working and one  
rear working halogen, 33,000 candle-  
power (375 737 lux each)  
G G G G Heavy-duty, hinged, bar-type grille  
G G G G Perforated engine side shields  
G G G G Rear service doors, lockable  
G G G G Reverse alarm – Switchable to 97  
dB(A) or 111 dB(A) (conforms to SAE  
J994, J1446)  
G G G G Vandal protection – Engine access  
door / Fuel tank cap / Rear service  
doors / Instrument panel  
L L L L Winch drive  
Operator’s Station  
Electrical  
G G G G Batteries, two, 160-min. reserve  
capacity, 950 CCA  
G G G G Bypass start safety cover at starter  
G G G G Master electrical disconnect switch,  
lockable  
G G G G Built-in diagnostics – Fault code  
retrieval / Onboard diagnostics for  
monitors, controller(s), wiring, gauges,  
sensors, etc.  
G G G G Built-in Operator’s Manual storage  
compartment and manual  
L L L L Cab – Air conditioning, 33,000 Btu* /  
Fresh air intake heater/pressurizer,  
400 CFM, 40,000 Btu/hr. (11.7 kW)  
(conforms to SAE J1503, J1535D) /  
Front window and two door wind-  
shield wipers/washers  
G G G G Deluxe suspension vinyl seat –  
Adjustable armrests, thigh support,  
backrest, height/weight, and fore-aft  
(conforms to SAE J899)  
Hydraulic System  
G G G G Oil-to-air hydraulic cooler  
G G G G Lift cylinders  
G G G G “O” ring face seal fittings  
G G G G Quick-drop hydraulic valve (Semi-U  
blade) (optional with All-Hydraulic  
[PAT] dozer blade)  
L L L L All-Hydraulic (PAT) dozer blade with  
grille “up-loop” plumbing  
G G G G Two-spool hydraulic system  
G G G G Three-spool hydraulic system (stan-  
dard with PAT blade)  
L L L L Four-spool hydraulic system (with  
PAT blade)  
L L  
L Cupped end bits (except All-Hydraulic  
[PAT] dozer blades*)  
L L L L Straight end bits  
G G G G All-Hydraulic (PAT) dozer blade  
(included in SAE operating weight)  
G G  
G Semi-U (High Production) dozer  
blade (included in SAE operating  
weight)  
G G G G Tilt cylinder hose protection  
Blade trash rack  
L
G G G G Deluxe suspension cloth seat  
G G G G Deluxe air suspension vinyl and  
cloth seat  
L L L L Environmental fluid drains  
L L L L Extended rigid drawbar with pin for  
pull-type implements (for 850C LT  
included in SAE operating weight)  
G L L L Heavy-duty transverse case cover  
(standard for WT with PAT blade)  
L L L L Perforated hood for trash envi-  
ronments  
L L L L Rigid drawbar with pin (standard for  
LT and WT with PAT blade) (for 850C  
WT, 850C LGP included in SAE oper-  
ating weight)  
G G G G Electronic monitor system with audi-  
ble and visual warning – Air restric-  
tion / Coolant temperature / Engine  
oil pressure / Ether injection on /  
Fasten seat belt / Hydraulic filter  
restriction / Low alternator voltage /  
Transmission filter restriction / Trans-  
mission malfunction /Transmission  
return to neutral / Transmission tem-  
perature  
L L L L Auxiliary hydraulic lines to rear  
L L L L Oil sampling test kit  
Undercarriage  
G G Chain guides  
G G G G Front idler and bolt-on sprocket  
chain guides  
G G G G Sealed and lubricated chain  
G G G G Oscillating track-frame system  
G G G G Pinned front track-frame crossbar  
system  
L L L  
L L  
Trash bars front and rear  
L Grille housing mounted counter-  
weight (N/A with PAT blade)  
G G G G Engine rpm digital display (selectable)  
G G G G Floormat  
Net engine power is with standard equipment including air cleaner, exhaust  
Specifications and design subject to change without notice. Wherever applicable, specifications  
are in accordance with SAE standards. Except where otherwise noted, these specifications are  
based on units with rollover protective structures, full fuel tanks, 175-lb. (79 kg) operators, and  
standard equipment.  
system, alternator, and cooling fan, at standard conditions per SAE J1349 and  
DIN 6270B, using No. 2-D fuel at 35 API gravity. No derating is required up to  
10,000-ft. (3050 m) altitude. Gross power is without cooling fan.  
Also available: winches, fair-leads, log arches, skidding grapples, trash pack-  
ages, landfill protection packages, cable plows, side booms, field-installed cab  
for ROPS, ROPS heater, and fire suppression systems.  
DKA850CII Litho in U.S.A. (03-05)  
 

Indesit Freezer IN C 325 AI User Manual
Indesit Washer Dryer W 143 S User Manual
Indesit Washer Dryer WIXXE 147 User Manual
Integra Car Video System DSR 48 User Manual
Jabra Headphones GN1200 User Manual
JVC Car Stereo System KW NT300 User Manual
JVC VCR LPT0591 001A User Manual
Kambrook Hot Beverage Maker KAK35 User Manual
Kawasaki Cordless Drill 840557 User Manual
Kompernass Blender KH 527 User Manual